PLUMBING BASICS: BEFORE INSTALLING A BATHTUB

Plumbing Basics: Before Installing a Bathtub

Plumbing Basics: Before Installing a Bathtub

Blog Article

This Resource

They are making several good pointers about Installing A Bathtub in general in the content underneath.


Installing A Bathtub
Setting up a bath tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and also often, tiling abilities. Replacing an old tub with a new one is additionally a reasonably challenging project. If the old bathtub is conveniently available, the project can relocate quickly; if you need to open up a wall surface to get rid of the old tub and place the new bathtub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will need an assistant to move out the old bathtub as well as embeded in the brand-new one. Make sure you have actually certified yourself for the job as well as fit attempting it. Instead of employing a specialist to take over a halfway-completed task, it is better to consider employing one prior to you begin. Possibilities are you may require a professional plumber to make tube links.
This post will help you mount a brand-new tub in your washroom if you have actually currently acquired a brand-new tub and also don't require to change the arrangement of your previous water pipelines.
Your devices as well as material list need to make up the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installation


    First of all, the supporting framework supplied with the bathroom must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to stop stress on the bathtub.
    Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the supplied washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final setting.

    Removing Old Taps


    If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly troublesome because of the limited accessibility that is usually the situation.
    Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will originate from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
    Prior to carrying on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

    Mounting the Bath tub


    Making use of both wood boards under its feet, position the bathtub in the called for position. The wood boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
    The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub up until the level reviews degree.
    To mount faucets, fit the bottom of the furthest versatile faucet connector to the proper supply pipeline by making a compression sign up with; then do the very same for the other tap.
    Switch on the water and examine all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub as well as also check the overflow outlet and the typical outlet for leaks.
    Ultimately, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the bath tub must wait up until the bath tub has been utilized at least when as this will resolve it right into its last setting.

    Suitable New Taps


    If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a connection to the current supply pipelines.
    If you require to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next off, place the tap in the placing opening in the bath/basin ensuring that the washing machines are in area between the tap and the sink. Safeguard the faucet in position with the manufacturer given backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The previous kind ought to be connected to the tap finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub


    In the location where the bathroom satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break a rigid seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, leading to problems with dampness and also feasible leakages to the ceiling below.
    You can pick from a selection of coloured sealants to assimilate your components and fittings. They are marketed in tubes and also cartridges, and also can securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to enable the movement experienced when the tub is in usage. The sealer can break relatively early if you do not take into consideration this motion prior to securing.
    Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly offered on the market. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky and grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Do you really like more info about A Step-by-Step Guide to Installing a Bathtub? Leave a short review directly below. We would be glad to know your thinking about this posting. In hopes to see you back again before long. Sharing is good. You won't know, you may just be helping someone out. Thanks for going through it.


    Protect your space!

    Report this page